Monday, November 15, 2010

Web-Frames

Back to the shop! Web-frames for the Kwila stand. The web-frames create the drawers pockets I'm wanting in the stand and give the stand way more strength than it needs heh.
Pictured above, using the band saw to cut the slip tenon mortise.

On the table saw cutting shoulders for the tenons

BAM! Fit slip tenons with allowances for easy clamping.

I guess I forgot to photograph the center piece for the drawer partition. Well, it is fit with shooting board and block plane then doweled into place. Pictured is applying the Kwila front edge.
I have enough good Kwila to have made the frames of all Kwila but I like the look of the Maple. A nice splash of colors for the curious. That and the drawer sides are going to be of the same Maple, it will all be nice and bright in there.

Fitting the frame to the stand and making it all nice and square. The nice thing about the web-frames is that when gluing up I know my stand will be square if the frame has a seamless joint. That is without ridiculous pressure.

Both frames fit with splines and dowels... I don't think they are going to go anywhere heh.
On to edge work and pre-finishing.

The first glued assembly of three, scary! It went smoothly enough, I'm glad I had an extra set of hands.
I can sense the light at the end of the tunnel... not there yet!

Thursday, November 11, 2010

A Man and a Mill

A little while ago I was invited down to Spencer, IA to meet a man with a passion and a mill. Tuesday morning I made the 4 hour trip.
Spencer, I was informed is a bit of a railroad town denied the railroad. Charming yet strange. Brandon is the resident wood nut heh.
I have seen and participated in a bit of chainsaw milling and I have seen a little of a band saw mill in action but have never seen the whole process let alone operate one. Brandon showed me some of the ropes.
It was a great experience gaining new appreciation and having a good time.

I saw a log of Walnut among a few others behind the barn that looked promising to me. Brandon got it on the mill with a tractor and asked is I wanted to "drive" the mill. After getting the log oriented in the way we thought best suited it we went ahead with flitch cutting the log. Perhaps the easy way to mill but my preferred method.

This Walnut log was about 22" in diameter and 8.5 feet long. The mill was pretty easy to operate. Up and down, forward and back, and a speed control. Then again, a hand plane is pretty easy to operate in theory.
The belt drive decided to take a short smoke break as it was displeased with some of my effort. Brandon assured me all was fine.

Whoo Wee! You don't see logs/lumber like that every day! I don't anyway. Clean and  mostly straight with only one sizable knot to work around.

Don't get drool on your key board...

Staked and stickered. all 8/4 (cut green at about 9/4) with the pith plank being about 10/4.

Next I was wondering about a log of Bur Oak out back. Nice straight and long. This one fought though. After the first pass we hit a nail. Then another. The log was getting shorter due to cutting sections with metal off. You can see the start of some black staining due to the nail(s). Then hit some copper too!? Ugh. One thing lead to another with some tools and we had to retreat for the time being.

Beautiful color and grain in this section. I hope more can be salvaged!

Well sir thank you for the time and hospitality, I shall return for more wood. So watch out!

Trials

    Tired and weary, roll to the side. The clock reads seven o’clock. It’s Sunday. I worked late last night. Would like to rest though I know it wont come.
    Today is the last day of a three-day event at the gallery, I’m scheduled to work elsewhere at four. Off to the gallery, I’m the first one there after the director. People walk in, eyes glance, and bodies turn back to the door. Some make little conversation. One lampshade was sold.
    A rumble comes from my stomach. I need fuel before work.
    Walk into work looking forward the sustenance in hand. There is no place to sit, all seats taken. Sit in back on the floor, it’s almost four. Go to the bathroom to change out of some dress clothes. Start the work day by picking toilet paper off the floor. Walk behind the counter to handle the dishes and stock neglected by my co-workers as my shoes stick a little to the floor.
    How does this place go on? Why am I here? I want to go home to my bed. Tomorrow morning I’ll be in my shop again.

Thursday, November 4, 2010

Stand Joinery

Last time I left with mapping out mortises. Here are the mortises being cut!
I put the shop-made X-Y table back into action because I felt with the angles in the joinery it may be easy to lose a visual reference when cutting free-hand.

Fast Forward the tenon fitting and here is the rail stalk with four tenons on each side! Looks kind of neat and holy crap is it strong!

With the floating tenons glued into the rails I'm looking to get a "seamless" transition between legs and rail on the inside which is a drawer pocket side. Yes, I know my plane's mouth is a bit big. I had replaced this smoother with a Vera one that then de-laminated ... it felt so good in hand and made my hands smell good ha. Oh well.

Using little 45 degree cradles to hold the legs for edge treatment, after pillowing was done.

Aaaaand more pre-finishing. I have a good amount of work left to do with this stand but I figure I want to glue the legs to the side aprons now to eliminate unnecessary variables down the road. To make the glue-up happen I need to pre-finish first. Then I am making the web-frames and assembling the rest of the stand around those.

Thursday, October 28, 2010

Enter the Stand

Two of three planks of Kwila that came from Cormark Int atop the new set of saw horses. I finally don't have to do a balancing act while trying to rough cut lumber with only two horses again. Don't let looks deceive you. Even though the horses are made of little they are sturdy! I gave one a test by sitting on it for at least 30 sec (my butt started to hurt ha). Two of them can handle me sitting on a plank while scrub planing said plank.

Getting all four legs from one plank. This was a great selected plank! Clean grain that has a subtle curve to it. A true rift toward where the center of the tree would be for the front legs and quarter-leaning to the outside for the rear legs. This plank is also for far the best working Kwila I've laid edge to. The other two planks don't work as nice though.

Legs with the insides shaped and apron parts to the left.

It has been a long time since I've made legs at vertical angles to the joining aprons. I forgot about the more time involved. I've left the outsides of the legs straight and square for now to help me with joinery... such as making sure the angled joints equal 90 degrees seen above.

Now this is starting to look a bit complicated, or at least intensive. The side aprons are so fat because they will also be acting as my drawer pocket sides. Even though my aprons will end up canted to the side I'm once again keeping two sides square. I've planed the joinery to be vertically straight because I felt it would be easier to avoid any twisting in assembly due to not getting angles quite right. With that planed I have room to do some twin 1/4" tenons. I'm splitting those up into four 1/4" tenons because they would otherwise be so tall. Though this doesn't allow for as much glue area on the tenons (though there's already plenty) it does make the mortises stronger resulting in a stronger joint... in my theory ;).
Here's to not pulling my hair out with these!

Monday, October 25, 2010

Saw Horses

So Here I am, in wait for lumber to come to my door for the stand of the Maple Showcase project. I was thinking of making some saw horses after finishing the showcase but time has presented itself now.
On the table are all the rough dimensioned parts for four horses. The little "pony" there was made at school as an exercise in tenons, it also happens to be a 1/2 scale of the low horses out at IP. I'm making the taller horses though.

Here is some free-hand mortising in a foot piece. The ones at school are wedged tenons but I'm making stub tenons here.

Live tenons. There are 16 tenons in a set of four of these horses, I figure I would use them as another exercise in live tenons.
The shoulders cut and waste removed with table and bands saw. I use a chisel to cut out the corners of the tenon then round it with files to fit the rounded mortises... morti?

Here's a dry-fit tenon. Yes there is space horizontally because these are to be wedged tenons. It has been a long time since I have wanted to put through joinery in a piece, haven't done it since MCTC (before IP). These utilitarian aids probably need it though. The "leg" pieces are relatively thin and with the use that these guys are going to see (hopefully) they could benefit from a joint being mechanically strong too.


LOTS of edges to treat! But I don't want to be grabbing at sharp things when working so treatment they received!
The horses are all assembled except for the top cross piece. There is a lap joint in the top of the leg about 3/4" deep and a lap in the cross piece about 1/4" deep. The top piece is not to be glued into place in case it is ever needed to be replaced. The 1/4" dowel is not compressed any further than what came from the factory and is a tight fit. One will need to apply a fair amount of force to get the cross piece off but not enough that anything is in danger of breaking.

Tah-dah! A set of saw horses ready to be used! They are 30" tall and the top cross member is 18" wide.
I would also like a set in the 20-22" tall range, another time...

Sunday, October 17, 2010

Material Frustration

So this is the 100th post huh? Too bad it deals in frustration heh.
The doors hung, edges treated, and finish applied the cabinet is basically done. It's strange just how plain it looks without those pulls. I feel the addition of the pulls will make a world of difference (hopefully for the better ha).
The Maple has finished a littler more yellow than anticipated. Only used 4 thin coats of extra blonde shellac and one coat wax. The material I had aside for the stand is Golden Narra, a golden yellow color of course. I got started mocking up a stand and then took Narra samples to the cabinet only to have mu stomach turn. It was too close and tooooo much yellow going on >:/ .
I think if the match was closer to the Maple yet of differing "qualities" say Oak of sorts, Hickory, and so on it could work. However seeing as how this is supposed to be more of a "show piece" I'm wanting a higher contrast.
The other side of this disappointment, other than the money needed for new material, time taken to find/get new wood, and just wanting to wrap this project up, is that the Narra I have is 2 7/8" thick! I was going to utilize the + 8/4 in my leg shapes. Now I have to re-design the stand!

As I have said many a time before, there is no where good to go here for a selection of lumber. Also it is disappointing that we really don't have any domestics that are in the honey brown color range (like Teak).

I went to the whole of two local commercial lumber yards and found nothing for my cabinet (no surprise). I though perhaps Jatoba could work but there was only 5/4 to be had at one place. So look like I need to order something.
Called up my guy at Cormark (Jason who is awesome by the way) and briefly chatted with him about ideas and what he had in. I think Teak would be quite fitting but man, at $30 PER b/f? I'm thinking I need to get 20 b/f here to get what I need... $600 for a stand I wasn't prepared to pay for? If this was a commissioned piece it would be a different story.
There are other options like Iroko or some sort of Meranti, but I'm a bit uncomfortable with those as I have never worked with them and haven't seen anyone else who has. I really don't know how those woods age. I called Cormark because I knew they have some Kwila which is what I think I will go for unless he has some Brown Doussie or something, whish I doubt they do.
So while I wait for stand wood I will do some sketching of a new stand and thought I would at least start on the saw horses I've been wanting which is what the Ash pictured above is for.

However, while at one place I did find this guy. I saw it and immediately thought "that's perfect for the desk I want to do!" Except for the LARGE check of course. I figure I would need to rip this piece a couple times to work with it anyway and the check is decently contained across maybe 3 grain lines, and the fact that it would be a veneered top makes it a little easier to work around.
There wasn't enough material to get the rest of the desk from though and it's only 4/4 so it will really only serve as a possible top >:(. One reason why I don't like these kind of shops, they use material indiscriminately. How can you do that with such a beautiful tree!?! The grain, the color! AH!
I figure at $35 for a beautiful top, I would regret not taking it.
So now here's a challenge... find other walnut with similar enough color to make the rest.

I heartily dislike going to these kinds of places. At least around here. At 27 I'm one of the young guys coming in and get treated like an uneducated child. They are the ones who look confused at me when I say I'm looking for straight grained rift sawn 8/4 material. Most don't actually know what Rift is. What am I building? It doesn't frickin matter, I know what I want and need. Oh, you want leg stalk? Well that plank there is quartered... I said RIFT. Do you know know that furniture is 3 dimensional? You get two side with straight grain quartered but what about the other two? Garbage. Oh, well this plank has some rift then that one over there... Those are different colors! We tend to look for "interesting" wood. Oh so what you do is cut part of the trunk to get the crotch and the another part of the trunk to get the butt of the tree. So you're trying to make "Nakashima" slabs out of any tree you get and wasting the prime real estate without even thinking about it. Boy getting that rift sounds like a lot of waste. Yeah? well what I'm building may be better for the tree, it will be beautiful and have a much longer and happier life than your failed "Nakashima" table (don't use his name in vain ha) or your mismatched gaudy gun rack.
Every time I leave I wish to never return.