All the substrates had been made, now they all have veneer. That's not to say they have edges though. Above the lumber-core back apron getting veneer. Clamped this up at the end of a day so that I could use my bench and a big heavy flat caul.
For the side stretchers I decided to go with bent laminations. I may have mentioned that I'm low on Walnut for this project, and I already had the form from the side apron veneered lamination. Walnut is also a good candidate for lamination. Something lighter in color and more dense such a Maple will show the seams more readily.
Even with Walnut's favorable attributes for such a technique I took the time to hand plane each surface after they went through the thickness planer and before the lamination. This plane is still new to me but it feels like it will continue to be a good performer given the right attention.
Here is a still rough result! I used 5 eighth-inch strips of Walnut glued together over the curved form I used for the side aprons. The glued layers is what holds the shape. Under close inspection they look like pretty clean and tight seams to me :).
Before I get focused on joinery I want to rough mill stock for the drawer pocket web-frame that is to be made of Oak. Attack of the kiln-dried White Oak again! This was after re-sawing for the two long frame members. Good thing I cut them way over thickness! I was afraid something like this would happen... and it did ha.
While these and the other frame pieces are settling a bit hopefully I can get on to the main joinery. Still have to figure all that out though!
In more news, I received a shipment of lumber for my next project which will be a pair of Nightstands. This is Steamed European Beech coming from A&M in Cambridge, ON. It's hard to see the relatively fine grain in this shot but it is not as nice of selection I was hoping for. I had a feeling it would basically be pulled from the top of a pallet but for half the cost as Gilmer was asking I figured I'd give it a shot... I may have learned a lesson.
This perhaps will just supply challenge in an otherwise more simple project and practice in doing the best with less than ideal material which I'm sure I will continue to struggle with ;).
In further more news, Art-a-Whirl is this weekend! May 20-22. The Northrup King Building is included in this event where Blue Sky Galleries resides and within reside some of my pieces. I will be in attendance when I can to hopefully meet, greet, and chat with some folk!
Perhaps see you there!
Monday, May 16, 2011
Friday, May 6, 2011
Substrate City
Aloha it's once again time for substrates! Ha
As I get further into this project I realize that for such a simple looking end result there is a fair amount going on with this desk. Even in the substrates!
The for drawer pocket partitions are made with flat birch ply, two different thicknesses though. The side aprons are being made by bent lamination of 1/8" ply lams. Then the back apron is lumber-core constructed... and I still have to make a decision on how to construct the two side stretchers!
Building something of the sort with an organic intention is neither quick nor easy. If it was, we'd see more of it I think.
Above some bake-ins are being applied to a drawer pocket component.
Shaping a Poplar mold for the bent laminations.
Here is the core lamination all clamped up. I'm using 1/8" Poplar "sheets" combined as a flexable caul. The ply core with be then given bake-ins before it goes back on the mold to get veneer.
While that was going attention was turned to the lumber-core back apron piece. Quater-sawn Poplar. I'm using lumber-core so I can curve the outside to the shape of the desk-top and keep the back flat which will be part of the drawer pocket.
Clamps came off the bent lamination and went on to press the Oak veneer for some drawer pocket parts. I kept my "press" set-up I had for veneering the panels in my Side Tables in hopes that I would need it again. And it just seemed a good size to keep around. Less fussing around makes my life easier, yay.
While the veneer was going I got to the bake-ins on the bent lam side apron cores. The bake-ins need to be cut in a curve also of course heh.
Aaaaaaand cleaning up the long bake-ins for these curved surfaces. I went with a spokeshave to accomplish this.
Wheeew now that the substrates are mainly done I can get to the veneering. The up coming couple weeks may be a bit touch and go because I'm starting a new part-time job hopefully as a barista on a high-end "coffee bar" and bakery (yay/yum) and will have some overlap with the other. Somewhat decent timing though as I only have enough clamps to do one veneer clamp-up at a time and my Father looks to be starting a sizable project and will be in the shop.
Hopefully I wont get too cranky from being out of the shop! ha
As I get further into this project I realize that for such a simple looking end result there is a fair amount going on with this desk. Even in the substrates!
The for drawer pocket partitions are made with flat birch ply, two different thicknesses though. The side aprons are being made by bent lamination of 1/8" ply lams. Then the back apron is lumber-core constructed... and I still have to make a decision on how to construct the two side stretchers!
Building something of the sort with an organic intention is neither quick nor easy. If it was, we'd see more of it I think.
Above some bake-ins are being applied to a drawer pocket component.
Shaping a Poplar mold for the bent laminations.
Here is the core lamination all clamped up. I'm using 1/8" Poplar "sheets" combined as a flexable caul. The ply core with be then given bake-ins before it goes back on the mold to get veneer.
While that was going attention was turned to the lumber-core back apron piece. Quater-sawn Poplar. I'm using lumber-core so I can curve the outside to the shape of the desk-top and keep the back flat which will be part of the drawer pocket.
Clamps came off the bent lamination and went on to press the Oak veneer for some drawer pocket parts. I kept my "press" set-up I had for veneering the panels in my Side Tables in hopes that I would need it again. And it just seemed a good size to keep around. Less fussing around makes my life easier, yay.
While the veneer was going I got to the bake-ins on the bent lam side apron cores. The bake-ins need to be cut in a curve also of course heh.
Aaaaaaand cleaning up the long bake-ins for these curved surfaces. I went with a spokeshave to accomplish this.
Wheeew now that the substrates are mainly done I can get to the veneering. The up coming couple weeks may be a bit touch and go because I'm starting a new part-time job hopefully as a barista on a high-end "coffee bar" and bakery (yay/yum) and will have some overlap with the other. Somewhat decent timing though as I only have enough clamps to do one veneer clamp-up at a time and my Father looks to be starting a sizable project and will be in the shop.
Hopefully I wont get too cranky from being out of the shop! ha
Monday, May 2, 2011
Return to Deskland
Alrighty! After finishing up the Cherry Display Cabinet and taking a breather I'm back on the Walnut Desk I started a bit back.
Last I have just got the Walnut veneer on the desk top and smoothed that all out. Applied edges were next for me. I decided I'd just use the iron I had in my other smoother for now and tune up the new plane. I'm feeling the pinch as it were. Trimming these little edges isn't really critical enough to judge a plane by however I do like the feel of it thus far :).
Above is the mouth of my new plane. Not too shabby if you ask me ;D.
After the long edges were applied and trimmed I went to the short cross-grained ones. In this case there is no overlap of edges because the legs will be integrated into the top. This means the order of the edges is "less" important. I chose to do the long ones first so I could plane with the grain and not have to worry about cross-grain blow-out going across the end-grain edges.
I used a number of 1/8" thick slices of Poplar as flexable cauls gluing one side at a time.
Above is a plank of White Oak that will fulfill the drawer pocket and side components of the desk. I have had this plank for a little over a year and just took it out again to look it over. I marked where I think I want to get my drawer pocket partitions from but I don't like to make hasty cuts in "virgin planks" particularly because I was originally saving this plank possibly for a pair of side tables to go with the Oak Coffee Table I made. Soooo I came up from the basement to do some online stuff.
On that note I have hesitantly started a facebook page. The little lady has been suggesting it to me; I figure I'd give it a shot!
Nicholas Nelson : facebook
I've also put a link to it in the side links here and on my website.
Check it out if you wish!
Last I have just got the Walnut veneer on the desk top and smoothed that all out. Applied edges were next for me. I decided I'd just use the iron I had in my other smoother for now and tune up the new plane. I'm feeling the pinch as it were. Trimming these little edges isn't really critical enough to judge a plane by however I do like the feel of it thus far :).
Above is the mouth of my new plane. Not too shabby if you ask me ;D.
After the long edges were applied and trimmed I went to the short cross-grained ones. In this case there is no overlap of edges because the legs will be integrated into the top. This means the order of the edges is "less" important. I chose to do the long ones first so I could plane with the grain and not have to worry about cross-grain blow-out going across the end-grain edges.
I used a number of 1/8" thick slices of Poplar as flexable cauls gluing one side at a time.
Above is a plank of White Oak that will fulfill the drawer pocket and side components of the desk. I have had this plank for a little over a year and just took it out again to look it over. I marked where I think I want to get my drawer pocket partitions from but I don't like to make hasty cuts in "virgin planks" particularly because I was originally saving this plank possibly for a pair of side tables to go with the Oak Coffee Table I made. Soooo I came up from the basement to do some online stuff.
On that note I have hesitantly started a facebook page. The little lady has been suggesting it to me; I figure I'd give it a shot!
Nicholas Nelson : facebook
I've also put a link to it in the side links here and on my website.
Check it out if you wish!
Monday, April 25, 2011
Wall Cabinet Wrap Up
It took longer than expected (of course) to get glass but I got it and was able to wrap things up.
Seems as though it has been a while since the last post on this.
Pictured is mortise making for door hinges. This was just after I refinished my butt chisel handles. You can see the difference between those and the original finish on the bench chisel.
Consoles (shelf supports) in process. Kind of cute heh. I went with Jatoba for the little bits in the cabinet. It will age to a darker rusty red color which should go nicely with the aging cherry.
Consoles finished! There will be two shelves for this cabinet. I made two sets plus three extra... biffed the last one of the third set but I was expecting that ha. This way there is extra in case something should happen to the others. Don't know what but it's better to be prepared :).
This is a scarey part that I had been putting off. After fitting and hanging the door. I mortised the door for the same pull I made for the first door. Now it was time to cut into the FINISHED carcass to make a recess for the pull.
Started out with marking the recess with a pencil. Went at it with a chisel. Then made a sanding block to fit the shape I wanted. Finished it up and made the little profile with a knife. I dig it.
Phew!
Received the glass shelves and "bulk" sheet of glass for the door panes. Got to cutting the glass for the door myself.
I think this is a good thing to be able to do. I like to know that I can make these kinds of panes fit just right. Not tight but not sloppy. It allows me to work with smaller tolerances, which I like.
Once the glass was cut and put into place I marked the mullions on the sticks that hold the glass in place. Pictured above was after cutting the waste with the band saw. Used chisels to fit and clean them up.
Drilling hole for the brads that will hold the glass in.
SO CLOSE!
Actually it is done. Cleaned up the sticks, softened their edges, glued the pull in place, finished everything that needed finish, installed glass into the door, and hung the door. :D
Alas I have another waiting game. I ordered a pair of studio strobes (photo flash lights) and was given notice a couple days later the they are on back order. They say it will take another week or two but I have had bad experience with things on back order in the past :/.
While I'm waiting for those I will of course resume work on the Walnut Desk :).
Seems as though it has been a while since the last post on this.
Pictured is mortise making for door hinges. This was just after I refinished my butt chisel handles. You can see the difference between those and the original finish on the bench chisel.
Consoles (shelf supports) in process. Kind of cute heh. I went with Jatoba for the little bits in the cabinet. It will age to a darker rusty red color which should go nicely with the aging cherry.
Consoles finished! There will be two shelves for this cabinet. I made two sets plus three extra... biffed the last one of the third set but I was expecting that ha. This way there is extra in case something should happen to the others. Don't know what but it's better to be prepared :).
This is a scarey part that I had been putting off. After fitting and hanging the door. I mortised the door for the same pull I made for the first door. Now it was time to cut into the FINISHED carcass to make a recess for the pull.
Started out with marking the recess with a pencil. Went at it with a chisel. Then made a sanding block to fit the shape I wanted. Finished it up and made the little profile with a knife. I dig it.
Phew!
Received the glass shelves and "bulk" sheet of glass for the door panes. Got to cutting the glass for the door myself.
I think this is a good thing to be able to do. I like to know that I can make these kinds of panes fit just right. Not tight but not sloppy. It allows me to work with smaller tolerances, which I like.
Once the glass was cut and put into place I marked the mullions on the sticks that hold the glass in place. Pictured above was after cutting the waste with the band saw. Used chisels to fit and clean them up.
Drilling hole for the brads that will hold the glass in.
SO CLOSE!
Actually it is done. Cleaned up the sticks, softened their edges, glued the pull in place, finished everything that needed finish, installed glass into the door, and hung the door. :D
Alas I have another waiting game. I ordered a pair of studio strobes (photo flash lights) and was given notice a couple days later the they are on back order. They say it will take another week or two but I have had bad experience with things on back order in the past :/.
While I'm waiting for those I will of course resume work on the Walnut Desk :).
Thursday, April 14, 2011
Plane Break
I put in an order for the glass for the Cherry Cabinet on Wednesday. It wont be done till Friday at the earliest I suspect. What to do now. Well I took some time to pick up around the shop but I also had a milled plane black laying around for a few weeks and decided to go to town on a new smoother to replace the last one of Vera that delaminated. I took a bunch of pics in case anyone viewing this blog is not familiar with "krenovian planes".
So, I got a 3"x3"x12" blank from the local "woodworking store". They sell these as turning blanks though I don't really know why this is such a popular size but it works great for most hand plane projects.
I scraped the wax off and let it sit for a while. Then did some milling getting the cheeks and the main body cut out. I let these sit stickered for a few weeks for them to move as they please.
When I finally got back to the blank yesterday I flattened and dressed the sides and body. Then cut the iron ramp out on a band saw.
Used my block plane to dress and square up the iron ramp.
Then using the iron itself to help set the distance between the ramp and the front I drilled holes in the top corners for locator dowels. Trimmed the dowels flush so they wouldn't interfere with the glue-up.
With the dowels in place the cross-pin holes were drilled at 5/16". Use the block that was cut out as a backer for the first hole drilled.
That same block was used to get cross-pin material. I got two cross-pin blanks and a bit left over for shoulder cut tests on the table saw. The rest of the block will be used to get a wedge and can be saved in case of the need for a mouth insert.
Pin shoulders were cut on a table saw. Then the tenons are made round to fit with a chisel and files.
A relief was made for the chip-breaker cap-screw using a 3/4" router bit on the router table.
After triple checking everything and giving the glue faces a acetone wipe I glued the plane up with cauls and flaw board.
I do happen to have these cauls and flaw board "laying around" for plane making :).
I left the glue-up over night and came back to it today. Took the glued up block out of the clamps and ran the bottom over the jointer once. Then to the band saw to rough out the final shape.
Some like their planes rougher than others. I tend to like mine relatively shaped smooth as is more comfortable for my small soft hands hahah ;).
Tada! There it is fit with a wedge. It isn't in working order yet. These planes always seem to move around a little bit in the first stage of their life so I'm just going to allow that to happen for a bit before I get to fine tuning. I also want to order a new iron for it. The one I have seen here is wearing a bit short.
Here's hoping it will be a loyal performer!
This project along with cleaning up a bit has been good for me to get back in tune with the shop space as I still hadn't acclimated since my return from IP. I'm also enjoying a couple "bonfires" cleaning out my scrap bins that have over flowed from winter.
Alas the seasons change and it can be easy to lose one's way with our short Minnesotan Summers ha. We'll see... ;p
So, I got a 3"x3"x12" blank from the local "woodworking store". They sell these as turning blanks though I don't really know why this is such a popular size but it works great for most hand plane projects.
I scraped the wax off and let it sit for a while. Then did some milling getting the cheeks and the main body cut out. I let these sit stickered for a few weeks for them to move as they please.
When I finally got back to the blank yesterday I flattened and dressed the sides and body. Then cut the iron ramp out on a band saw.
Used my block plane to dress and square up the iron ramp.
Then using the iron itself to help set the distance between the ramp and the front I drilled holes in the top corners for locator dowels. Trimmed the dowels flush so they wouldn't interfere with the glue-up.
With the dowels in place the cross-pin holes were drilled at 5/16". Use the block that was cut out as a backer for the first hole drilled.
That same block was used to get cross-pin material. I got two cross-pin blanks and a bit left over for shoulder cut tests on the table saw. The rest of the block will be used to get a wedge and can be saved in case of the need for a mouth insert.
Pin shoulders were cut on a table saw. Then the tenons are made round to fit with a chisel and files.
A relief was made for the chip-breaker cap-screw using a 3/4" router bit on the router table.
After triple checking everything and giving the glue faces a acetone wipe I glued the plane up with cauls and flaw board.
I do happen to have these cauls and flaw board "laying around" for plane making :).
I left the glue-up over night and came back to it today. Took the glued up block out of the clamps and ran the bottom over the jointer once. Then to the band saw to rough out the final shape.
Some like their planes rougher than others. I tend to like mine relatively shaped smooth as is more comfortable for my small soft hands hahah ;).
Tada! There it is fit with a wedge. It isn't in working order yet. These planes always seem to move around a little bit in the first stage of their life so I'm just going to allow that to happen for a bit before I get to fine tuning. I also want to order a new iron for it. The one I have seen here is wearing a bit short.
Here's hoping it will be a loyal performer!
This project along with cleaning up a bit has been good for me to get back in tune with the shop space as I still hadn't acclimated since my return from IP. I'm also enjoying a couple "bonfires" cleaning out my scrap bins that have over flowed from winter.
Alas the seasons change and it can be easy to lose one's way with our short Minnesotan Summers ha. We'll see... ;p
Monday, April 4, 2011
Where's that swing?
Getting back home, it has been difficult to get back in the swing, find that momentum. Being gone for a couple weeks, jet lag, odd schedules at the part-time, and plan old being beat.
I have managed to get some work done back in the shop. I'm back on that Cherry Display Cabinet. Doing this door again. After taking it very slow and carefully with milling the frame stock down I'm feeling pretty confident of its stability.
Made a new template for the panes of glass. Ugh, that's another thing... Glass shelves. I just can't find a quality glass cutter around here! As it looks I'm going to have to opt to have the glass cut and ground then get another grinding wheel and put buffing wheels on it to polish the edges myself. I've never polished glass before. I've used buffing wheels with metal before. I would think it would be fairly similar.
Frame dry-fit with panel rebates and all about ready to be glued up. The second time around the production has gone smoother which is nice and encouraging.
Currently the door has been glued-up and fit to the cabinet opening. There's still enough work to be done to keep me busy for a couple days... if I can finally really get in the shop that is. I still have a couple non-shop things to do :/.
Another factor I feel playing against me is that of a little funk :( heh. I haven't been feeling as connected to the work as I usually am. This seems to come and go with all sorts of people in all sorts of walks of life.
I think it's good to reflect on one's "way" and asses "their path". Seems to be part of "the human condition" at least for me. It just sucks that it gets in, what seems to be, the way ha.
In attempt to reconnect, I took some time later in the evening to give my little chisels some love.
I like these Ashley Iles butt-chisels but I'm not fond of some of the fit and finish of them. The Bubinga handles covered in hard thick finish, the cheap ferrules. I stripped the hard finish off with scrapers and files and re-finished them with a single thin coat of oil. Also I took some sand paper to the ferrules to clean them up a bit.
I'm going to need to replace my 1/8" and 1/4" chisels soon and have been wondering about switching to a whole new set. I'm still undecided... I wish more people made quality butt-chisels.
I have managed to get some work done back in the shop. I'm back on that Cherry Display Cabinet. Doing this door again. After taking it very slow and carefully with milling the frame stock down I'm feeling pretty confident of its stability.
Made a new template for the panes of glass. Ugh, that's another thing... Glass shelves. I just can't find a quality glass cutter around here! As it looks I'm going to have to opt to have the glass cut and ground then get another grinding wheel and put buffing wheels on it to polish the edges myself. I've never polished glass before. I've used buffing wheels with metal before. I would think it would be fairly similar.
Frame dry-fit with panel rebates and all about ready to be glued up. The second time around the production has gone smoother which is nice and encouraging.
Currently the door has been glued-up and fit to the cabinet opening. There's still enough work to be done to keep me busy for a couple days... if I can finally really get in the shop that is. I still have a couple non-shop things to do :/.
Another factor I feel playing against me is that of a little funk :( heh. I haven't been feeling as connected to the work as I usually am. This seems to come and go with all sorts of people in all sorts of walks of life.
I think it's good to reflect on one's "way" and asses "their path". Seems to be part of "the human condition" at least for me. It just sucks that it gets in, what seems to be, the way ha.
In attempt to reconnect, I took some time later in the evening to give my little chisels some love.
I like these Ashley Iles butt-chisels but I'm not fond of some of the fit and finish of them. The Bubinga handles covered in hard thick finish, the cheap ferrules. I stripped the hard finish off with scrapers and files and re-finished them with a single thin coat of oil. Also I took some sand paper to the ferrules to clean them up a bit.
I'm going to need to replace my 1/8" and 1/4" chisels soon and have been wondering about switching to a whole new set. I'm still undecided... I wish more people made quality butt-chisels.
Sunday, March 20, 2011
A bit of a Blur
Oh boy, it's been a bit of a blur here. I don't do so well with time changes and I've gone through two of them on this trip.
Well trip began with visiting one Dan M... DannyMac? hehahhe Looking through lumber, spinning around Vancouver, some coffee and beer. Went down to the beach to see where his chainsaw milling takes place. Pretty cool, I wouldn't mind being able to do the same now and again ;).
Thanks for your time and hospitality Dan!
Onwards/back to the school!
It was great to meet all the passionate crafts-people here, to reminisce on memories past, and taking some new memories for the future.
The program has changed a bit since I was there but the quality and underlying goals remain.
There is, of course, great working being done this year. I didn't get to pull my camera out on everyone's project but I snapped a few...
Raul is stationed at my old bench, it seems to treat him well. He is making a lovely little jewelry display case for his wife, a jewelry maker, of Boxwood and English Sycamore. Above is one of his panels getting applied edges.
Meredith across from him is working on a lovely Danish inspired low console/coffee table. I think those through tenons are going to look pretty hot Meredith! ha!
Jesse is making a pipe wall cabinet of Caltalpa and Black Limba. I haven't been the biggest fan of either of these species, but these planks coming together in this cabinet of his is looking mighty fine.
Melissa is making a desk not hugely different from the one I'm working on. Her's is of Kwila and Narra, with drawers coming from the sides.
This is a mini mock-up of Hong's. Very cool. I think it could be very successful as a coffee table.
Steve Wolf finished and presented the second of a mating pair of end table/cabinets of Zebrano and Walnut. Well done sir!
Andrea is working on a wall cabinet of Claro Walnut, Monterey Cypress, and Swiss Pear featuring a display area, and an enclosed space. Pretty sharp.
Dave is reproducing a rocking chair made by Roberts a number of years ago. A great chair it is.
Jay has been spending time on a media stand with drawers made of Kwila. His plank of Kwila is a bit cranky but it's looking good!
Christian, from Denmark, is a highly meticulous worker... a regular Craig Johnson heh. Making a small tool chest of Boxwood and Maple. These woods call for precision work and Christian is surely meeting the challenge.
Josh is a young man somewhat strikingly similar to myself and my mode of work... also a musician. He's tackling one of JK's silver chests. These Maple drawers will be set into a Spalted Maple carcass. Good luck Josh!
Kylle is working on a lovely little floor standing cabinet made of a familiar material to me heh... Euro Cherry. Great work Kylle. He can show you his work on his blog here: http://kylle221.wordpress.com.
Howard has had years of experience as a carver. I can see how the plank he selected and his form speak to him and each other. It may be a little tricky but it will be lovely in the end. I'm sure he'll be looking forward to making happy shavings after break.
I've also been reminded how awesome this little coffee grinder is! I want one!!!
Thanks to eveyone who made this trip possible and for the kindness, hospitality, conversations, inspirations... and the food haha ;). Please keep in touch and show me your projects when they're done!
It is coming time for me to leave the coast again which is a bittersweet affair. I love the land, people, and culture here. Especially the multitude of cultures drawn to the school. At the same time my shop and work are calling me. Also I am looking forward to get back to special lovely lady back home...
Well trip began with visiting one Dan M... DannyMac? hehahhe Looking through lumber, spinning around Vancouver, some coffee and beer. Went down to the beach to see where his chainsaw milling takes place. Pretty cool, I wouldn't mind being able to do the same now and again ;).
Thanks for your time and hospitality Dan!
Onwards/back to the school!
It was great to meet all the passionate crafts-people here, to reminisce on memories past, and taking some new memories for the future.
The program has changed a bit since I was there but the quality and underlying goals remain.
There is, of course, great working being done this year. I didn't get to pull my camera out on everyone's project but I snapped a few...
Raul is stationed at my old bench, it seems to treat him well. He is making a lovely little jewelry display case for his wife, a jewelry maker, of Boxwood and English Sycamore. Above is one of his panels getting applied edges.
Meredith across from him is working on a lovely Danish inspired low console/coffee table. I think those through tenons are going to look pretty hot Meredith! ha!
Jesse is making a pipe wall cabinet of Caltalpa and Black Limba. I haven't been the biggest fan of either of these species, but these planks coming together in this cabinet of his is looking mighty fine.
Melissa is making a desk not hugely different from the one I'm working on. Her's is of Kwila and Narra, with drawers coming from the sides.
This is a mini mock-up of Hong's. Very cool. I think it could be very successful as a coffee table.
Steve Wolf finished and presented the second of a mating pair of end table/cabinets of Zebrano and Walnut. Well done sir!
Andrea is working on a wall cabinet of Claro Walnut, Monterey Cypress, and Swiss Pear featuring a display area, and an enclosed space. Pretty sharp.
Dave is reproducing a rocking chair made by Roberts a number of years ago. A great chair it is.
Jay has been spending time on a media stand with drawers made of Kwila. His plank of Kwila is a bit cranky but it's looking good!
Christian, from Denmark, is a highly meticulous worker... a regular Craig Johnson heh. Making a small tool chest of Boxwood and Maple. These woods call for precision work and Christian is surely meeting the challenge.
Josh is a young man somewhat strikingly similar to myself and my mode of work... also a musician. He's tackling one of JK's silver chests. These Maple drawers will be set into a Spalted Maple carcass. Good luck Josh!
Kylle is working on a lovely little floor standing cabinet made of a familiar material to me heh... Euro Cherry. Great work Kylle. He can show you his work on his blog here: http://kylle221.wordpress.com.
Howard has had years of experience as a carver. I can see how the plank he selected and his form speak to him and each other. It may be a little tricky but it will be lovely in the end. I'm sure he'll be looking forward to making happy shavings after break.
I've also been reminded how awesome this little coffee grinder is! I want one!!!
Thanks to eveyone who made this trip possible and for the kindness, hospitality, conversations, inspirations... and the food haha ;). Please keep in touch and show me your projects when they're done!
It is coming time for me to leave the coast again which is a bittersweet affair. I love the land, people, and culture here. Especially the multitude of cultures drawn to the school. At the same time my shop and work are calling me. Also I am looking forward to get back to special lovely lady back home...
Subscribe to:
Posts (Atom)


