Wednesday, December 29, 2010
Here's a little flyer for the up-coming "First Thursday" at the Northrup King Building. Don't know how many folk viewing this blog are near the Minneapolis area but feel welcome to come by Thursday the 6th, see the new piece &/or heckle me ha.
Just took this cabinet to the gallery today and managed a little rearranging. I was looking to group all of my stuff together hopefully in a manner conductive to the pieces themselves within the boundaries of the tight space. There is a space in the back corner of the show space I thought would be nice. There isn't much there now and it's pretty spacious. Problem is that it's all the way in back so not as attractive to foot traffic. However I would be able to lay things out in similar ways they may appear in a home.
The director suggested the entry. I suppose it's a nice gesture having the first spot people see. However I've seen that the entry way is not a place that people linger. They step in and eyes grow wide wanting to see everything. Then it is just an after-thought on the way out, minds already turned off moving on to the next studio. All that and it's a smaller space. Baby steps I guess. Hopefully I will start to sell, then later we'll see heh.
This time 2 coats orange shellac, 2 coast extra blond, 1 wax.
It already has a nice color to it. It should age to a nice rich tone.
At the gallery today I noticed how nicely my Cherry Pedestal is aging. At first it was so close to the AD Maple I used for the top but now there is a clear distinction. A couple months ago it looked a bit gray, monotone, and a little drab. Now it's looking deeper, redder and... sexy?
I WAS going to use some of that same Maple I have left over but it doesn't look like it's going to work :(. The two clean pieces I have are too different in color/reflection, and they are too small to make up the back panel on each own. I think Kiln dried Maple is going to be too bright, to much contrast. Maybe it'll look stellar for a month but in a year... not for this piece. I have a lead on some more Maple. Hopefully it'll work out!
Wednesday, December 22, 2010
This photo shoot seemed to go better. Perhaps I'm getting a little hang of this? Ha not crossing my fingers.
Thanks again to Craig and Carol Johnson for lending me their lights! Lights of my own are on my list I promise heh.
After last time I figured it was better to use a higher ISO level to get brighter though slightly more grainy photos than smoother dark ones. For use on the internet it is basically no visible difference in grain but in print I suspect there will be.
Haven't messed around with them too much in post but don't think they'll need much work.
Also the size of this cabinet wouldn't allow me to get full landscape shots which is what my website is based on as my backdrop is too narrow :/. I'm going to have to figure something out...
Tuesday, December 21, 2010
Before I left I was getting some good work done.
It is said that it only takes 10% of the total time in a project to get 90% completed. Well the carcass of this wall cabinet has sure come together pretty quick.
Above pictures one of the sides being cut to final dimension. The stop-block ensures that the next side will be "exactly" the same size.
Dressing the end grain of the sides straight and true... and smooth.
I have a block for the right side and a block for the left side. Temporarily nailed into the sides to hold them during operation.
These pieces still seem to be moving on me a little bit. The trip over the weekend was a good way to get away from them for a few days. Hopefully they have sorted themselves out and I can touch them up when I get back to them.
I find the Veritas spoke shave to be more to the liking of my hands. More ergonomic for me with nice placements for your thumbs and fingers close up to the blade. Allows me to work more comfortably and with more control. However the Veritas round bottom shave has a heavier radius than needed which decreases the stability of the cut for me. I tried both at IP from my classmates and seem to do better with the LN's shallow radius. So now I have one. The LN is prettier than the Veritas heh.
Saturday, December 11, 2010
My plan for the day was to rough mill parts for the Cherry cabinet and go to work at the part-time for the rest of the day conveniently getting paid while I let the wood settle a bit. My car, however is going no where in this snow so I'm snowed in with nothing to do ha.
I figured I'd chat here a little bit.
This is basically the yield of the whole plank pictured yesterday. It may not look like much, and it may not be, but beyond cutting off sap there was very little waste after joining and planing the stock... perhaps 20-25% Which is pretty damn low for this kind of work!
Pictured there is the top, bottom, and sides of the carcass. Also the frame members for the door. I still need to find the back panel frame parts, mullions (pieces separating glass in the door), and the horizontal partition or "stage" as I like to call it in these kinds of cabinets. Finding the partition is going to be the trickiest. Usually I get it from the same plank as the carcass which was not possible in this case. I wont be able to find a "perfect" match but hopefully I'll find something that looks good.
I've always had mixed feelings about Cherry. It's every where. Whenever you talk to people who aren't "bit by the wood bug" they only seem to care or know about Oak, and Cherry. I've seen a lot of "bad" work in Cherry. A lot of misused perhaps abused Cherry. So many woodworkers go on and on about how great it is (many of whom are the misusers). It's gratuitous.
All this gives me poor connotations with the wood. However Cherry IS nice and CAN be used to much success. It's relatively light and sturdy. It works very well and has little blunting effect. It has potential for a variety of finishing choices. It has lovely depth of color (when not stained [as it should be ;) ] ). The wood even smells a lovely soft sweetness. The trees themselves are romantic sights in bloom and bearing fruit.
It seems a lot of these connections are lost in much of the work I see in Cherry. I would love for this piece to come together and for an audience to be able to sense these things, the "nature" of the material. Perhaps, if it is a success, they may wonder why other work in Cherry isn't like this? ... That may be a stretch but it is nice to think about and perhaps wish or strive for.
I have a sudden craving for some cherry lambic.
Friday, December 10, 2010
Yay! My paper work finally has a home beyond a drawer in my room ha.
MCTC, IP, and my IP class photo :). I still want to make a little shelf for my JK Plane but will leave that for next break maybe.
Love those little steps, I can't get away from them now.
Next up is a wall hung display cabinet in AD Cherry!
For those in the "Krenov circle" this kind of cabinet is not new. A form so simple and elegant is bound to be come to by a variety of people independently, and one may expect, be repeated.
I love this form and have been waiting for a good time to build one. The specifics and details will vary with the voices of the lumber and maker. It is not and perhaps cannot be an exact "replica" of an existing piece.
The Cherry lumber has already put in a request: smallish. This is the best plank of cherry out of a small flitch and still has some defects to be weary of. I think I will go for about 1/2" bigger in height and width than the mock-up.
Also this time I'll be using a French Cleat to hang the cabinet due to the properties of the wall it is to go on. A cleat is easy enough but what gets to me a bit is the space needed in the back of the cabinet. One might say that an extra 3/8" or so is no big deal. Sure, but with a small cabinet that amount can be somewhat significant in a visual sense. I'm pretty into stripping down to "essential" space and size. The problem is that the "show space" (interior) of the cabinet may feel slightly small if I make the carcass the size I see fit, or the carcass might seem a little deep to get the show space I feel good with.
Currently I'm siding on the show space side. Probably because of a drive for function I tend to have.
Monday, December 6, 2010
I'm using my boring machine to dill holes for the drawer pulls. Pretty handy to have one of these to cut out variables of using a hand drill.
Here posts were cut to size, and tenons/shoulders cut on the table saw. There are two posts joined at the tenon here as the pieces are easier to work like this.
Holes being drilled are for the bails.
I machined them in pairs connected at the tips. Once again, much easier/safer to work with them like this. Tenons/shoulders on the table saw, and used a forstner bit to cut that round.
There's only going to be one shelf in this piece but I'm making 8 consoles. How much of a drag would it be to lose one of these little guys and not be able to use the shelf!
They are made of Olive and are quite yellow now. I think I'm going to let them oxidize a bit before I do a photo shoot. They should reach a mauve-ish brown in between the Maple and Kwila.